Fiat 500 Replacement Key Fob

It might be time to replace the battery if the 500 remote key fob isn't working. However, if you replace the battery and it continues to stop working then the issue could be elsewhere.

At United Locksmith, we specialize in making new keys for old cars. We have all of the tools and components needed for this service.

Dead Coin Battery

The most frequent reason why your fiat 500 remote key programming 500 key fob will not unlock or lock the doors is due to a dead battery. The coin cell battery in the key fob will drain quickly when you don't use it often enough. If your remote is beginning to show signs of a loss in range or stopped functioning and the battery is not working, it could be dead.

Metal clips hold the battery securely on the key fob. If the clips are loose, it can cause contact issues which will prevent the remote from receiving power. Utilizing a small screwdriver, pull the clip that holds the retaining pin open to remove the current battery and insert a new one. Choose a battery that is the same voltage, size and specifications as the original.

The key fob could also be damaged or corroded by water exposure. Even a small bath in soapy, warm water could damage the chip. It is recommended to keep your key fob in a dry environment.

Water Damage

If your key fob doesn't work properly, it could be due to water damage. The rubber seals on key fobs prevent them from getting damaged by a tiny splash or drizzle of water. However, it's crucial to keep the keys of your car away from the ocean, washing machine, and pool.

The key fob is equipped with an electronic chip that sends an alert to the immobilizer system of your vehicle. The chip is what allows the 500 to lock and start. If it gets wet, however it will cease to work.

You can try cleaning the inside of your key fob's electronics with isopropyl alcohol or an electronic cleaner to see whether they're still working. However, it's recommended to purchase a replacement from a dealer rather than trying to repair an item that is submerged in salt water.

While a replacement fob can cost a bit of money, it is a lot cheaper than paying for your Fiat 500 to be towed to the dealer and repaired! You can also fix it yourself with only a few steps. Make sure you have the correct battery type before attempting to open your key fob. You can find step-by-step instructions for any car keyfob on the internet.

Faulty Chip

The chip inside the key fob is in direct communication with the immobiliser of your car to ensure that your vehicle will only start when correct keys are used. If the chip is damaged, or damaged in any way it will not start.

A faulty chip can occur due to many reasons, but the most common cause is water damage or an unresponsive battery. It is best to leave the task to a professional locksmith who will be able to replace the chip in a short time and at a an affordable cost.

If your key fob will not work after being exposed to clean rain or tap water take it off the battery. Wipe down the electronic component using an old towel. If the key fob does not function, there's an opportunity that it is a fried component and needs to be replaced.

A few people turn to their dealer when they are in need of a new Fiat key fob, but this is a costly option. If you are seeking a cost-effective solution to get your fiat panda key replacement key fob (Ravn-puckett-2.thoughtlanes.net) fixed make sure you contact United Locksmith. We have the equipment and know-how necessary to fix your Fiat key fob in a quick and professional manner.

Faulty Receiver Module

Fiat key fobs send an electrical signal to the vehicle which will unlock and close doors (and [Redirect-302] start the car for vehicles with an automatic transmission) up to 50 feet. There are many reasons why a fob could not function. It could be due to a dead battery damaged by water buttons, worn ones, a receiver module issue and signal interference or a malfunctioning electronic chip.

If the fob is placed in a pocket that suffered a severe trauma, like being dropped on hard floors or being washed in the washing machine the fob may not be able to communicate with the car's Body Control Module (BCM). This is because the BCM is a secure system that can only accept a signal from a genuine key, and not from any other.

You'll need to replace the fob in case this happens. A professional locksmith will manage the entire process of replacing your key including programming a new one for your 500. In fact, they could provide you with a duplicate key that functions exactly the same way as the original fob (and costs only a fraction of the price).